расчет оценки стоимости чистых активов бланк скачать
Главное меню:
Интересное
расчет оценки стоимости чистых активов бланк скачать, Script to forcefully enable/disable FileVault on Mac., Error when trying to enable FileVault on … - Apple Community, man page fdesetup section 8, Mac: Enable FileVault without User Interaction : r/AZURE - Reddit, Manage FileVault with device management - Apple Support, Important commands for the CLI tool "fdesetup" | Forrest, What is fdesetup on macOS? - macosbin.com.
Hi, It sounds like you're encountering a frustrating issue with enabling FileVault on your MacBook Air running macOS Ventura. Here are some troubleshooting steps and suggestions to help resolve the problem:1. Verify Admin Account PermissionsEnsure the admin account you're using has full administrative privileges. Sometimes, admin accounts can become corrupted or lose certain permissions.To check:Go to System Preferences > Users & Groups.Verify that the account you're using is listed as "Admin."2. Check for FileVault Pre-RequisitesFileVault requires certain conditions to be met before it can be enabled:The startup disk must be formatted as APFS.There must be no pending disk errors or issues.The system must have a valid recovery key or iCloud account linked for recovery.To check the disk format:Open Disk Utility.Select your startup disk and confirm it is formatted as APFS.3. Reset NVRAM/PRAMResetting the NVRAM/PRAM can sometimes resolve issues with FileVault.Shut down your Mac.Turn it back on and immediately press and hold Option + Command + P + R.Keep holding the keys for about 20 seconds, then release them.4. Enable FileVault via TerminalSince the GUI method isn't working, you can try enabling FileVault using the Terminal. Here's how:Open Terminal.Run the following command to check the FileVault status:fdesetup statusIf FileVault is off, proceed to enable it.Use the following command to enable FileVault:sudo fdesetup enableYou will be prompted to enter the admin password and create a recovery key. Save the recovery key in a safe place.If this command fails, note the exact error message and proceed to the next step.5. Check for Disk IssuesEven though you've already run Disk First Aid, it's worth double-checking for any underlying disk issues that might prevent FileVault from being enabled.Boot into macOS Recovery:Restart your Mac and hold Command + R until the Apple logo or spinning globe appears.Open Disk Utility and run First Aid on your startup disk again.If any errors are found, attempt to repair them.6. Check for Configuration Profiles or MDM RestrictionsIf this Mac is managed by an organization (e.g., through an MDM solution), there might be a configuration profile preventing FileVault from being enabled.Check for profiles in System Preferences > Profiles.If you find any profiles, review their settings or contact your IT administrator.7. Reinstall macOS (Without Data Loss)If none of the above steps work, you can try reinstalling macOS Ventura without erasing your data. This can fix any system-level issues that might be causing the problem.Boot into macOS Recovery.Select Reinstall macOS and follow the on-screen instructions.Additional Notes:If you encounter specific error messages (e.g., during the fdesetup command), please share them so I can provide more targeted advice.Make sure you have a backup of your data (e.g., via Time Machine) before attempting any major changes like reinstalling macOS.Let me know how it goes!, Reason: The fdesetup utility is unable to determine which keychain to use to access the master encryption key for FileVault full-disk encryption. Solution: To resolve this error, you need to explicitly specify the keychain to use by adding the -keychain option to the fdesetup command., 4. Enable FileVault via Terminal. Since the GUI method isn't working, you can try enabling FileVault using the Terminal. Here's how: Open Terminal. Run the following command to check the FileVault status: fdesetup status. If FileVault is off, proceed to enable it. Use the following command to enable FileVault: sudo fdesetup enable.
fdesetup is used to enable or disable FileVault, to list enabled File- Vault users, or to add additional users after FileVault has already been enabled. When enabling FileVault, the tool can return a recovery key., fdesetup enable -user $loggedInUser -defer /private/var/root/recovery.plist -keychain -forceatlogin 0. This works just as I would expect it to. The user is trapped at the next login and can't log in without turning on FileVault., You can use device management configurations or the fdesetup command-line tool to configure FileVault. For a Mac with macOS 10.15 or later, using fdesetup to turn on FileVault by providing the user name and password is deprecated and won’t be available in a future release., The fdesetup tool allows administrators to enable FileVault for a specific user account or all users on the system, which encrypts the entire disk and protects the data from unauthorized access. It also provides options to add or remove individual users from the list of FileVault enabled users., fdesetup is used to enable or disable FileVault, to list, add, or remove enabled FileVault users, and to obtain status about the current state of FileVault. Most commands require root access and need to be authenticated with either a FileVault password, a personal recovery key (if enabled), and in some cases the private key from the installed , I just remembered that there is a command line tool (fdesetup) to manage Filevault. Strange, Apple removed the option in System Preferences. To remove the user "username": sudo fdesetup remove -user username To add the user "username": sudo fdesetup add -usertoadd username For more details: man fdesetup.